1220x2440mm
Marine Plywood
- Size 1220 × 2440 mm and 1250 × 2500 mm, or cut to size
- Thickness 2–30 mm
COM-83E79D
Get a Quote
Commercial Plywood
1220x2440mm
SKU: COM-120251
SGS tested
CE marked
ISO 9001
Specification
| Size | 1220 × 2440 mm and 1250 × 2500 mm, or cut to size |
|---|---|
| Thickness | 2–30 mm |
| Core | Poplar, eucalyptus, combi or birch core, depending on the weight and the machining |
| Face and back | Melamine, HPL, birch, pine, okoume, bintangor, eucalyptus, red or white oak, sapele, black walnut |
| Glue line | Interior grade as standard; specify WBP where the panel meets damp conditions |
| Face grade | BB/CP near-clean with occasional repairs; C/C allows repairs and knots — grade decides appearance, not strength |
| Use | Furniture, joinery, general construction. Not a marine panel. |
What this product does
-
1
Cross-laminated veneers
Alternating grain gives the panel its stability and its edge strength
-
2
Core sets the weight
Poplar, eucalyptus, combi or birch, depending on the machining
-
3
Glue line sets exposure
Interior as standard, WBP where the panel may see damp
-
4
Grade is appearance
BB/CP or C/C changes the face, not the strength of the panel
Description
Commercial plywood in 1220 × 2440 mm and 1250 × 2500 mm, from 2 mm to 30 mm, built from cross-laminated veneers around a poplar, eucalyptus, combi or birch core. Face and back can be specified across a wide species range, from okoume and bintangor to oak and walnut.
It is the general-purpose panel for furniture, joinery and construction, and the decisions that matter are the core, the glue line and the face grade. Core decides the weight and how the panel machines; the glue line decides where it can go, and interior grade is fine for a dry room while anything that may see damp — a kitchen carcass, a bathroom unit — needs WBP. The face grade is the one most often misunderstood: BB/CP gives a near-clean face with occasional repairs, C/C allows repairs and knots, and neither changes the strength. A buyer paying for a higher grade expecting a stronger panel has paid for appearance. Where a visible run is specified, keep one species across it, because a species change mid-wall shows even when the grade matches.
Confirm the core, the glue line and the face grade together when ordering, and tell us if the panel has to finish to a precise thickness for a rebate rather than assuming the standard tolerance will hold it.
Where it is used
Furniture carcasses
A panel that takes screws at the edge and holds a veneer face
Shop fitting
Flat, consistent sheets for visible panels and hidden structure
Sub-floor and structural work
Grades used where the panel is part of the load path
Export crating and packaging
A structural panel that survives a container
Frequently asked
What is the minimum order?
1 × 20ft container, mixed across products where the mix suits the project. A sample box can be arranged before the first container.
Can I see a sample before ordering?
Yes. Send the product and the size you are specifying, and we will confirm the sample and the lead time for it.
Does face grade affect strength?
No. Grade decides appearance — how much repair, how many knots, how uniform the face is. A BB/CP panel and a C/C panel from the same core and glue line carry the same load. Buyers often pay for grade expecting performance, and it does not work that way.
When do I need WBP rather than interior glue?
Where the panel will see damp or repeated humidity. Interior glue is fine for furniture in a dry room; a kitchen carcass, a bathroom unit or anything that may get wet needs WBP, and that decision is cheaper to make at order than to discover later.
Can I mix face species within an order?
Yes, faces can be specified per panel, but keep one species to a visible run. A species change mid-wall is obvious even when the grade matches.
Is the thickness tolerance tight enough for joinery?
Standard plywood tolerance applies; if the panel has to finish to a precise thickness for a rebate, tell us at enquiry and we will confirm what can be held rather than assume.
Trade terms
- MOQ
- 1 × 20ft container
- Lead time
- 15-25 days
- Payment terms
- T/T 30% deposit, balance before shipment
Final packing, freight and loading plan are confirmed in writing on the order quotation.
Related products
All in this category
50 × 150 mm section · interior ceiling
Ventilated WPC Ceiling Tube 50 × 150 mm
- Section 50 × 150 mm, supplied made to order to the run length
- Weight class Heaviest tube in the range — the hanger carries the section, so it fixes back to structure
CEI-7F162E
Get a Quote
50 × 90 mm section · interior ceiling
Easy-install WPC Ceiling Tube 50 × 90 mm
- Section 50 × 90 mm, supplied made to order to the run length
- Install Easy-install detail — the profile seats onto its fixing in one movement
CEI-C7A5CE
Get a Quote
50 × 75 mm section · interior ceiling
Suspended WPC Ceiling Tube 50 × 75 mm
- Section 50 × 75 mm, supplied made to order to the run length
- Suspension Suspended detail — hangs on hangers below the slab rather than fixing tight to it
CEI-3408AF
Get a Quote
50 × 60 mm section · interior ceiling
WPC Ceiling Tube 50 × 60 mm
- Section 50 × 60 mm, supplied made to order to the run length
- Visual weight The narrow end of the 50 mm-deep family — the face that will not dominate a low room
CEI-2442D4
Get a Quote
40 × 45 mm section · interior ceiling
Rot-proof WPC Ceiling Tube 40 × 45 mm
- Section 40 × 45 mm, supplied made to order to the run length
- Rot Composite core does not rot — the fixings and any timber batten behind it are what fail
CEI-EA5AC5
Get a Quote
Technical reading
- 50+ Countries shipped to
- 2003 Established
- 20,000 m² factory area
- 20 Production lines
- 80 Employees
- 15 Product lines
- 5M m² annual capacity
Ask about this product
Tell us the size, the quantity and the destination port. We will come back with price, lead time and the packing plan.
- Reply within one business day
- No obligation, no account needed
- Drawings and specs stay confidential
Get My Quote
The product name and SKU are filled in for you.